Prior to installation of flowIQ® 2250 the system should be cleanedĪnd flushed thoroughly. The transmitter turns on automatically when the frstġ/4 gallon of water has run though the meter.Ī small square is flashing to indicate that the The meter is still in transport mode with theīuilt-in radio transmitter turned off. The water flow has exceeded a preprogrammed limit for a minimum of 30 minutes,Īttempt of fraud. The water has not been stagnant in the meterĭuring the past 24 hours. The three segments will switch on alternately Mounting the meter in a downpipe, you must be aware that theĭisplay in that case will be ’upside down’. ItĬan be mounted vertically in an ascending pipe, it can be mountedĪt any angle and it can be mounted with the display pointing Thus, the meter can be mounted in a plain horizontal installation. Kamstrup Headquarters recommend that the display is mounted so Check valves mustīe mounted according to local regulations.įlowIQ® 2250 can be mounted at all angles and positions. The meter is supplied with a strainer in the inlet.
![how do i cut out parts of a photo using indesign cc 2017 how do i cut out parts of a photo using indesign cc 2017](https://1.bp.blogspot.com/-8EYgDtchv10/WBv5Xf6keXI/AAAAAAAAAOU/jbQcglgzLacCS9pNAxEpNpE5CcSlkGdSACLcB/s1600/Laptop%2Brepair%2Bmacbook%2Bretina%2Bbuy%2Bsale%2Bvancouver.jpeg)
Should be mounted on both sides of the meter. In order to facilitate replacement of the meter, shut off valves Dismount the meter from the system before When the meter has been mounted in the system neither welding The table below describes the different info codes in the display. Indicate if the customer is billed in e.g. They can be used to indicate numbers after the decimal point or The number of gallons or cu ft are displayed by nine large digits.īars over and under each digit are fully customizable, meaning that Tested and verified and the counter has been reset. When flowIQ® 2250 leaves Kamstrup Headquarters, it has been Surface and that couplings with similar pressure ratings are used.įor sealing, use the sealing wire holes on the lower side of the Of the couplings does not prevent proper tightening of the sealing Mounting the meter you must make sure that the threaded length Tighten an extra ¼ to ½ turn on each coupling. In a properly aligned piping system with new gaskets, you should beĪble to mount and tighten the couplings by hand.Īfter hand-tightening the coupling nuts, using an open-end wrench, Further details appear in the data sheet.ġ.1 Permissible operating conditions/measuring ranges Service, must be carried out by an authorized Kamstrup ServiceĬertain changes of configuration, however, are possible via theīuilt-in optical eye without dismounting the meter from the
![how do i cut out parts of a photo using indesign cc 2017 how do i cut out parts of a photo using indesign cc 2017](https://i0.wp.com/lorieannj.com/wp-content/uploads/2012/06/dreamstimefree_145045.jpg)
To service the meter without breaking the seal. Read this guide before installing the water meter.įlowIQ® 2250 is a compact electronic water meter used for waterĬonsumption measurement in the tap water supplies of homes,įlowIQ® 2250 is hermetically closed, and it is, therefore, impossible Step 2: Align the antenna by using the terminals and steering pin
![how do i cut out parts of a photo using indesign cc 2017 how do i cut out parts of a photo using indesign cc 2017](https://4.bp.blogspot.com/-ve9b3xxeKVg/WBv5XozlL2I/AAAAAAAAAOg/rX0qRM885mEUlnpCmy0D1Vr0zzT53ygMQCLcB/s1600/laptop_mac.jpg)
Step 1: Push the base of the helix antenna through the seal housing. Interference that may cause undesired operation. Operation is subject to the following two conditions:ġ This device may not cause harmful interfenrence, andĢ This device must accept any interference received, including This device complies with Part 15 of the FCC Rules. No restrictions, since the source-based time-averaged output power RF Exposure compliance statement: This device may be used with Party responsible for compliance could void the user’s authority to
![how do i cut out parts of a photo using indesign cc 2017 how do i cut out parts of a photo using indesign cc 2017](https://cloud.netlifyusercontent.com/assets/344dbf88-fdf9-42bb-adb4-46f01eedd629/bf3eec0c-c2c2-4da7-b9e0-850a447dcc9f/visual-composer-website-builder-wp-image-24.png)
Make sure the terminal is dry and clean before clicking theĬaution: Changes or modifications not expressly approved by the NOTE! The antenna must only be mounted on the meter with the Tightening torques would be exceeded, a meter setter or yoke If a pipe installation is skewed to the effect that the prescribed Protection Class IP68 (Waterproof/submersible) Optional customer label, (not an option for Encoded Output version) Optical eye for reading and configuration